CONSTRUCTION OF (9 CLASSROOMS) SCHOOL IN BASIRMA SUB DISTRICT, ERBIL IRAQ
Brief Description of the Proposed Project:
Construction of (9 Classrooms) School in Basirma will provide access to the 225 host community students living in Rizgaryand Soresh neighbourhoods.
In 2030, the population of Basirma (out of camp) will grow from 13,490 to 16,862 individuals (Natural growth is 2.5% per year- according to the Directorate of statistics of the Kurdistan Region).
The students in primary school correspond to 11% of the population in town – in 2030, we can estimate that 1845 students will go to school in the town, which is an increase of 408 students compared to 2021, which existing schools cannot absorb.
In addition, in the 2021-2022 school year, 350 new students registered in primary schools (grade 1), while only 170 students graduated from primary to secondary school last year.
The demand for seats/ space in primary schools is clear. Access to education is already problematic in Basirma and will become solved by building the new school.
The project includes the following works:
Earth Work:
Site Preparation and Demarcation: according to Section 200 of IGTS and instructions of the site engineer. Removal of debris, grading, levelling to the appropriate level (+15cm to -15cm), clearance and layout and demolition of all existing materials such as (concrete, foundations, asphalt, and even rock layers) and transporting resulting materials (Debris) to an appropriate location outside municipalities border and approved by the site engineer, also removing and transport and reinstall and establish water network pipes and electrical networks and poles considering extra materials if needed, the price includes opening access road according to the work requirements, fixing proper centre lines in two directions and benchmarks according to the specifications, attached drawing, and instructions of the site engineer. The works should be done according to section (200) of IGTS, and any depth of cutting or Removing of Debris required for all the areas must be according to drawings and instructions of the site engineer. The site levelling according to the assigned design elevation should not note the 15cm depth; it will be in a different depth. The price includes providing and fixing 2 signboards for the site. The signboard should remain on-site till the end of the works and approval of project handover, then be removed in addition to fixing and setting out of BM control points.
Note: The contractor should Supply all materials and construct a well-equipped office (4 X 5)m with all the required (office furniture, laptop, camera, scanner, colour printer, WC) for the site engineer before starting the works.
Excavation works excavation in all types of soils (even rock layers, asphalt, or existing foundation concretes), including backfilling with sub-base material and compaction. The price includes compaction of the excavation base by using a compactor according to requirements of section 300 of IGTS and instruction of the site engineer.
Backfilling works: Supplying materials and filling with approved screened sub-base materials type B maximum size is 2” up to the DPC level for the building and where required within the area inside or outside of the fence such as aprons, walkways, garden, etc. with compaction (according to the specification) in layers 25 cm thickness, the compaction for garage and play yard must be not less than 88% MDD, and using anti termite chemical (cloreddin) to prevent and treat the white termite according to the instructions of the manufacturer and site engineer with all necessary works for the final two layers.
Provide materials and lay one layer of thick nylon under the concrete floors of tiles, granite, play yard, garage & aprons.
Provide and install HDPE Double wall corrugated (DWC) pipes 60cm, SN=8, consist joint, to divert the water passing the land, the price includes excavation of trench Min. (100 x 100) cm in all type of soils, even rocky, removal of debris to the sites as directed by Engineer, also the construction of manholes/collectors every 25m size (1mx1m) with variable depth according to the land slop using reinforced concrete for (base & walls), painting the inner side of the manholes with a suitable material, also provide Aheen cover with frame with all necessary fittings and accessories (Tee, Elbow 45/90 degree, adapters, coupling union for connecting, divider …etc.). Good compacting of sites before laying the pipes and backfilling the trenches of the pipes with approved materials, clean soil under & above the pipes, according to the drawings and Pipe Manufacture & Supervisor Engineer instructions.
CONCRETE WORKS: Including supply of materials (steel reinforcement, connection steel wires, cement, aggregate, water, sand, plastic cover for fixing the steel reinforcement in the proper level, bolts, nuts, washers, G. I. pipes, cutter machines, binder machine, etc.), and all necessary works, according to the section (600) of IGTS, drawings, and instructions of the site engineer.
Note:
1- Use new plywood for all support for wooden forms work, with Adjustable Steel Scaffolding Props and Formwork Jack Support.
2- Fy = 276 Mpa for 10mm,12mm steel bars. FY=414Mpa for 16mm,20mm,25mm steel bars
3. Allowable bearing capacity of soil = 100 KN / m2 (assumed).
5. the reinforcement details should be according to ACI detailing manual 2004.
6. New Plywood or standard formworks must be used for all structural parts.
Plain Concrete: Supply materials and cast plain concrete class (C10) 1:3:6 10cm (min. thickness) for under columns footing, wall footings, retaining wall, and foundation of a water tank stand to the required elevations and laying two layers of thick nylon. (The nylon should also cover the sides of excavation walls and extend on land 50cm to both sides of the excavation).
Reinforced Concrete for Strip Foundation and Footing: Provide all materials and cast reinforced concrete (ready mix C 25) for foundations, column footings, the foundation of the retaining wall, and the foundation of the water tank according to the attached drawings.
Slab and Beams Reinforced Concrete: Provide all materials and cast reinforced concrete (ready mix C 25) for the slabs, Beams, Tie Beams,fair-faced, stairs, lintels, windows decorate, according to drawings, specifications, and instructions of the site engineer.
Note: All the roofs must be treated and smoothened by a copter instrument.
Columns Reinforced Concrete: Provide all materials and cast reinforced concrete for the fair-faced columns (ready mix C 30), according to drawings, specifications, and instructions of the site engineer. All casting works must be done with a vibrator.
Plain Concrete for Partition: Providing materials and casting plain concrete for foundations of partition walls. The works should be done according to the site engineer's specifications, drawings, and instructions.
Expansion Joints: Provide materials and construction of Expansion joints vertically and horizontally for walls and ceilings using Hypalon tape plus Epoxy paste(Sagging vertical type) with a width of tape 15 cm and 1.5mm thickness. The price includes using a special 18 cm width Aluminum sheet or stainless steel brackets with elastic (intermediate rubber) inserts. Styrofoam, best (Turkish Quality) special pasty mastic according to the details and instruction of site engineer with all necessary materials and works for fixing. (The measurement will be done Horizontally {Horizontal projection from roof}).
Masonry works: Including provision of material, erection, pointing, curing, making expansion joint every (6m) with thickness 25mm with using of 25mm thickness compressed Polystyrene sheets, all necessary work according to section (500) of IGTS, drawings, and instructions of the site engineer.
Masonry works: Supply materials & construction of walls with Stone 25X20X15 cm with cement mortar (1: 3) and flush pointing inside and outside the walls with cement sand mortar (1:3) for, under DPC, The space between the stones should be filled with concrete (C25).
Clay Bricks works(Above DPC): Supplying materials & construction of walls with load-bearing clay bricks (20 X 20 X 40 cm) (INTERLOCKING TYPE) weight not less than (14Kg), with cement mortar(1: 3) for above DPC level the price includes filling joints vertically by cement and sand 1:3 and fixing the space with concrete columns by GI metal holdfast 30cm long 4mm thick at every alternative course fixed to concrete columns with two nos. shot fired cramps.
Hollow concrete block works: Supplying materials & construction of walls with hollow concrete blocks 12 X 20 X 40 cm with cement mortar(1: 3) for partition walls. The price includes filling the vertical joints between blocks with cement and sand 1:3.
ELECTRICAL INSTALLATIONS: Electrical points including provision and installation of all wiring (using excellent Jordanian type or KSA made) of wires 1.5 mm2 for illumination and 2.5 mm2 for the rest), inside Egyptian PVC conduits 20-25 mm with thickness 1.8mm galvanized boxes 0.9 mm thickness cables should be laid inside PVC pipes, all materials should be new (best type). All works should be done according to specifications and standard IEC76 and the instruction of a supervisor engineer.
Supply, install and test lighting points LED (36x1) Watt with all the required uses (single wires 1.5mm² ). The light switch plug should be (Edison, B.G, or FTM)or equivalent (if the mentioned brands are not available). (2-3) lamp controlled by one switch.
Supply, install and test lighting points LED (36x1) Watt with all the required, using (single wires 1.5mm² ). Fixing upper the whiteboard for the classroom, The light switch plug should be (Edison, B.G, or FTM)or equivalent (if the mentioned brands are unavailable). (2-3) lamp controlled by one switch.
Supply, install and test LED (36x2) Watt lighting points with all the required use (1.5mm² ). The light switch plug should be (Edison, B.G, or FTM)or equivalent (if the mentioned brands are not available). (2-3) lamp controlled by one switch.
Supply, install and test lighting points LED 18Watt (outdoor) IP 65 with all required using (single wires 1.5mm² with a suitable cable tray or cable conduit). The light switch plug should be (Edison, B.G, or FTM) or equivalent (if the mentioned brands are not available).
The price includes installing photocells.
Supply materials, installing, connecting, and testing electrical LED lights (60x60cm)(72 W) with all annexed parts using (2x1.5)mm2 wires inside false ceiling (daylight type) with switch on/off all (2-3) lamp controlled by one button.
Supply materials, install, connect, and test electrical LED spotlights (12W) with all annexed parts using (2x1.5)mm2 wires inside false ceiling (daylight type) with switch on/off all (2-3) lamps controlled by one button.
Supply materials, install, connect, and test electrical LED spotlights (10W) with all annexed parts using (2x1.5)mm2 wires inside false ceiling (daylight type) with switch on/off all (2-3) lamps controlled by one button.
Supply, install and test socket 13 Amp. (Edison, B.G or FTM) (samples required for final approval)using (wires 2.5mm² (GC, GCCI, Hidayatm FTM, Edison).
Supply, install and test Main switchboard size (50 X 70 X 20)cm with base 20cm with doors made by iron plate, 2mm and Thermal Painting approved color.
Supply, install and test Main Circuit breaker 3 phase 100 Amp. (Schneider, Legrand) or equivalent.
Supply, install and test branch Circuit breaker 3 phase 60 Amp. (Schneider, Legrand) or equivalent
Supply, install and test branch Circuit breaker 3 phase 40 Amp. (Schneider, Legrand) or equivalent
Supply, install and test Circuit breaker(3*2)A. for control with signal lamps.
Supply, install and test Multi measurement digital gage with CT (200/5)
Supply and install current electricity meter (20-60)A kWh (Diyala) or equivalent sealed from the electricity directorate with all the accessories.
Supply, install and test Contactor Schneider type 125 Amp. With ( 3 X 25 A) CB and photocell switch and cable ( 3g*1.5 )mm2 for photocell feeding.
Supply, install and test FDB Circuit breaker, 18 lines (MES, alfanar)or equivalent, with MCCB 63A (Schneider, Legrand) or equivalent, including connections, interconnections, lettering, loop earth, etc., as required. The price includes the provision of a protection box.
Supply, install and test FDB Circuit breaker, ten lines (MES, alfanar)or equivalent, with MCCB 40A (Schneider, Legrand) or equivalent, including connections, interconnections, lettering, loop earth, etc., as required. The price includes the provision of a protection box.
Supply and install joint box (30x20x10), 1.5mm thickness with suitable connector with all the accessories.
Supply, install and test electric Ceiling Fan (Panasonic, Philips, Toshiba) or equivalent (if the mentioned brands are unavailable) with the regulator; the price includes installing the electrical points by isolation copper wire 1.5 mm2 and 10mm steel bar for hanging the fan according to of instruction of supervisor electrical engineer.
Supply, install and test industrial Exhaust Fan size(10”) ( Japanese, Malaysian Quality, or equivalents.)mounted to the walls inside a wooden frame. The price includes supplying & installing until brake wire mesh, painting from outside, and control switch.
Supply, install and test industrial Exhaust Fan size(8”) ( Japanese, Malaysian Quality, or equivalents.)mounted to the walls inside a wooden frame. The price includes supplying & installing until brake wire mesh, painting from outside, and control switch.
Supply, install and test small size bell Indian Quality best type with fixing to the wall.
Supply, install and test big size bell Indian Quality best type with fixing to the wall control by the admin and cover the two floors.
Supply, install and test copper cable 4 X 10mm2+10mm2 best (Riyadh KSA Quality or Haditha Jordanian Quality) or equivalent type inside 2.5” diameter PVC pipes in the ground + installing above cable tray with all required and necessary works (such as hidden manholes) iron pipe 2” with an insulator to install the cable above the wall.
Supply and install and test split points using copper cable 4x6mm2 inside PVC pipe with electric switch 45 Amp best type, with using mini 32x3 Amp +10Amp with box, also install 3/4” PVC pipe inside the wall with fixing it to drain the water of split outside the building.
Supply and install lightning arrestor Turkish made ESE- sat (Aktif partner)(750) installed on the roof; the price includes Galvanized Iron pipe (5m, 3”) preparing and making Earthing system by (3 copper rode 1-2 m /18mm) improving Earth System materials(bentonite); welding together with cable 1 X 70mm2 and making manhole 40 X 40cm the instruction of supervisor engineer.
Supply material and Doing Earthing protection system for electric devices by using three copper rods 1m inside three ground holes and connecting the rode with the mainboard by cable 1 X 70mm2 and distributed to (FDB) by 1 X 25mm2 finally by 1 X 2.5mm2 for sockets, the price includes concreting manhole 40*40cm with covering it.
Supply and install and test split points using copper cable 4x3 mm2 inside PVC pipe with electric switch 45 Amp best type, also install 3/4” PVC pipe inside the wall with fixing it to drain the water of split outside the building.
Supply and install and test split points using copper cable 4x6mm2 inside PVC pipe with electric switch 45 Amp best type, with using mini 32x3 Amp +10Amp with box, also install 3/4” PVC pipe inside the wall with fixing it to drain the water of split outside the building.
Connection the building from the main switch to the main power using Copper cable 4 x 95 mm2 armoured two PVC layer best type Saudi with all accessories and necessary fittings, to be pass-through PVC pipe underground 1m depth with sand and concrete block 40x20x15 with warrant tape with all requirements.
Supply, install and test copper cable 4 X 25mm2+25mm2 best Riyadh KSA made type inside 2.5” diameter PVC pipes in the ground + installing above cable tray with all required and necessary works (such as hidden manholes) above dimension (40 X 40)cm.
Supply, install and test copper cable 4 X 16mm2+16mm2 best Riyadh KSA Quality type inside 2.5” diameter PVC pipes in the ground + installing above cable tray with all required and necessary works (such as hidden manholes) above dimension (40 X 40)cm.
Supply, install and test cable size 2 X 4mm2+ control switch Riyadh KSA Quality with a photocell to collecting and feeding external lamps throw inside 25mm diameter PVC pipes in the ground + installing above cable tray with all required and necessary works (such as hidden manholes) above dimension (40 X 40)cm.
Provide installation and test box joint (20 X 30 X 10)cm thickness of 1.5 mm with cover and thermal paint.
Supply and install and test 200 Liters production storage capacity an electrical water heater element of 2000 Watt with a thermostat. The tank plate is galvanized with 3mm thick The work includes all wiring 4x3mm2 and 30 Amp electric switch, plumbing works, pipes, fittings, and complete fixtures. The unit’s location should be as per the instructions of the Site Engineer.
Supply, install, and test 60 Liters, best type, production storage capacity, and an electric water cooler with two drains. The price includes connecting the water sources and electricity with all required materials and works.
Electrical Water Pump: Supply and install an electrical water pump according to the following specifications. The price includes all required electrical cables 3x4 mm2 (up to 50m); the cable must be put into a PVC pipe and lay in a trench with dimension 30 X 40 cm; then the backfilling with 10cm clean sand, 20cm clean soil, 10cm ordinary Concrete. Switches, pipes, water automatic PRESSURE SWITCH accessories, and connection with the school and a small steel protection pump room as indicated in drawing details:- Pump type KF1 ( Pentax type Italian made ), Size: 1.5” and HP = 1.5
Supply, install and test copper cable 70x1mm2 inside PVC pipes in the ground between the earth system and anti Electric stun bars.
Supply, install and test electrical board (40 X 50)cm containing circuit breaker 63amp Schneider type with 12 X 10amp circuit breaker Schneider. The price includes cable 4 X 4 KSA made between the distribution board and projectors inside PVC pipes (25 mm2) covered by concrete at a depth of 40cm according to of instruction of the supervisor electrical engineer.
Supply, Install and Test hand dryer 1000w-220v best available type.
Installing Sound System+Data Show+Printer:
Supply, install and test amplifier 240 watts (DVD+USB+FM) best type. The price includes all necessary works according to the instructions of the site engineer.
Supply, install and test loudspeaker 40-watt wall, best type, in each class, teacher room, and the corridor for both floors; the price includes all the required cables to connect the speakers with the main device in the manager room.
Supply, install and test, mick control best type.
Supply, install and test mike stand(tabletop) best type.
Supply, install and test Data Show (TV+USB+HBM+VGA) best type. The price includes all necessary works according to the instructions of the site engineer.
Supply, install and test Data Show Screen (230x220)cm2 LED electric control type. The price includes all necessary works according to the instructions of the site engineer.
Supply and install Data Show Base 1,5m length with all necessary works according to instructions of site engineer.
Supply and install Data Show Cable 25mm (VGA/HDM) for each classroom with all necessary works according to instructions of the site engineer.
Supply and install and test printer canon RUNNER 2520i model Resolution Reading: 600dpi × 600dpi
Copying: 600dpi × 600dpi
Printing: 600dpi × 600dpi, 1200dpi x 1200dpi (UFRll-LT only)
Number of Tones: 256 Gradations, the price includes installing table for papers, with one year warranty, with all necessary works according to instructions of site engineer.
Installing Security camera:
Supply and install a whole security camera system, including the following:
1- 25 fixed CCTV cameras (Dahua, Hitech) or equivalent (if the mentioned brands are unavailable)(indoor&outdoor) (5 megapixels) minimum with night vision with all the accessories (poles, stand) (if needed. With a warranty period of two years minimum.
2- Fiber optic cable for connecting the cameras with all the accessories, including the Fiber Media Converters, With a minimum warranty period of two years.
3- Switch Hub with minimum 24 ports, Switching capacity 48 Gbps, Forwarding capacity 35.7, HOL blocking prevention, Jumbo Frame 9216 Bytes, class of service 802.1p priority based, operating in (0°―40°)C. With warranty period up to two years minimum.
4- screen size will be 56" diagonal with (3840 x 2160) resolution and 150,000:1 dynamic contracts ratio, Built in tuner (ATSC/NTSC/Clear QAM) with aspect ratio 16:9, Audio System (20W (10w X 2) 2way 4 system), Audio/Video inputs: (1.RF in Antenna/Cable) (2.AV in) (3.Component Video In(Y,Pb,Pr)+Audio) (4.Digital Audio out (optical)) (5.HDMI 1.3/HDPC input 3 rear) (6.RGB in D-sub 15pin PC) (7.PC audio input) (8.LAN) (9.RS-232c in(control/service)) (10.USB 2.0 (JPEG, MPEG-4, Div X HD)) (11.Wireless control) (12.Headphone out) (13.WIFI)with warranty period two years minimum..
5- DVR 32 port
6- NVR 32 camera input with16 Terra: with a warranty period of one-year minimum.
7- Suitable size of DC UPS with a warranty period of one-year minimum.
8- Suitable size of the rack to fit all the devices.
Installing Transformer 100 Kva: All the work should be done according to the standard of the Directorate of Electricity; the contractor is responsible for coordinating with DoE before installing or providing the required materials.
Supply install, and test Electric transformer 100 kva IRAN Transfo Type Indoor; the price includes transferring. Test certification card from Erbil’s Electric distribution directory, iron channels, cable stand, and connection to the electric power. The price also includes the construction of a room (4x5)m with all the required (concrete block work, reinforced concrete, cement plastering, painting, doors, windows, etc.)
Supply, install and test electric board 25 X 80 X 100 cm by iron plate thickness,2mm with door and painting which contains bus bars 250Amp, circuit breaker 250 A fence type 3pole, kWh 200/5A (best type), multi measurement digital type, CT 200\5 A, signal lamp,3*2A circuit breaker, and all accessories according to supervisor engineer.
Supply and install high tension electric pole 11m GV Turkish made lattice-type the price includes iron angle channels Linked fuse 12Kva, lighting arrestor 11kv 10ka excavation concrete work with all accessories.
Supply and install 11m high voltage electric pole tubular Turkish-made gv. The price includes excavation, concrete work, pin insulators, and all accessories.
Supply, install and test high voltage cable 11kv XLP 3 X 150mm2 15-20kv with PVC pipe Iron clamp two final Joints(Ryckom), excavation, Filling, tiles, and concrete work.
Supply, install and test insulated copper cable 1 X 95mm2 double PVC cover. The price includes cable shoes and (GV) Iron bolts.
Supply materials and doing Earthing system protection by copper rod 1.5m with diameter 18mm the price includes copper bar conductor 1 X 50mm2 improving Earthing soil materials and all accessories to complete this item.
Supply, install, and test ACSR conductor 120mm2. The price includes insulators and connectors.
Supply install and test automatic change over switch 250 amp GMC LG contactor type original the price includes suitable board (140 X 90 X 40)cm the contactors connected with bus bars and contain timers, control circuit breakers, phase failer for main power and copper insulated cable 1 X 300mm2 to complete the item.
Supply, install and test lightning conductor protection system.
Supply, install and test final distribution circuit breaker 4 Fuse HAVELLS type Indian made with cable 3 x 4mm2 in the transformer room.
Supply, install and test copper cable 70mm
Sanitary (Plumbing) Installation: Includes supply and installation of materials, pipes, all kinds of fittings, valves, mixers, bibcock taps, P-traps, gullies with cover, supports, hangers, plug and clips, all excavation with backfilling, placing concrete 1:2:4,15cm thick under and around pipes, workforce for the installation and internal connection of the water system to hot and cold water and the main water supply system. All water pipes should be Polypropylene (PPR). Composite water pipes of min. 3 Layers of side walls (PPR/AL/PPR/PE), PPR-C inner layer, and a special mixture of AL middle layer should be coated with an external layer of PE (Polyethylene Layer) dark grey/black color to protect against ultraviolet rays, Different Outside Diameter (OD) as below, Min.PN16 Bars, suitable for drinking purpose/food grade, approved samples with all required fittings and accessories, Egyptian best type PVC pipes for sewerage system with all the necessary fittings. All new WS and SS work items should be tested before covering. Note: All materials should be the best-approved type; the work of external water connection (3/4” dia.) includes repairing (if any) all asphalt, concrete, and curb stone.
Providing materials and fixing industrial marble wash basin ( best type) with mixer (Turkish quality) + floor drains + Gully (Trap), using proper brackets and adhesive materials for fixing the basin with walls and fixing drain pipes inside walls(2.25”). the price includes making a square steel pipe 4”*4” frame 3mm thick with anti-rust paint.
Providing ceramic wash basin (wall mounted type) with mixer (Best Type, Such as GROHE, Hansgrohe, DURAVIT, Roca) + wall & floor drains + Gully (Trap)/room, using proper brackets and adhesive materials for fixing the basin with walls and fixing drain pipes inside walls & floor (2.25”). The price also includes providing and installing ceramic (50cmx25cm) (best type)for the wall behind the wash basin with a dimension of (1m width x 150m height) using tile adhesive materials (Kalakem flex type) with all the accessories.
Providing materials and fixing Eastern WC Ceramic ((Best Type, approved sample) ) with hidden Siphon/in-wall tank. + Gully (Trap) and cleanout accessories.
Western WC/Wall Hung/Mounted Toilet with the in-wall tank: provide, test, and install (Best Type, Such as GROHE, Hansgrohe, DURAVIT, Roca) with gully trap 4” dia, and flexible hose 5mm, handle tissue place complete in all respect.
Supply and install HDPE 1000 liter water tank; the work includes making an iron base support for the water tank and a layer of XPS under the tank, and drainage size ¾” locked by socket +Plug, etc., and all the required fitting and works.
Composite PPR water pipes: Supply and install water pipes of OD 20 mm, PN 16. The price includes all fittings and accessories, excavation (required depth), and backfilling of 10cm clean soil with all necessary works for cold water, with a painting by anti-rust paint for galvanized only.
Composite PPR water pipes: Supply and install water pipes of OD 25 mm, PN 16. The price includes all fittings and accessories, excavation (required depth), and backfilling of 10cm clean soil with all necessary works for cold water, with a painting by anti-rust paint for galvanized only.
Connecting the building with the main source of water using a standard PPR pipe of 32 mm OD & PN20. The price includes excavation of trench (30x70 cm.), covering pipes with (10) cm clean sand, and backfilling with all fitting and necessary works. The price also includes repairing asphalt or concrete pavement by 10cm if the pipe crosses these pavements.
PVC pipes (4)” diameter: Supply and install (4”)dia. PVC pipes best/approved type, 4.20 mm wall thickness with all necessary materials and fittings, according to section 1500 of IGTS and the instructions of the site engineer with all the necessary work. The price includes casting concrete type C (1:2:4) around the pipes 15cm thick for all pipelines.
PVC pipes (6)” diameter: Supply and install (6”)dia. PVC pipes best/approved type, 4.20 mm wall thickness with all necessary materials and fittings, according to section 1500 of IGTS and the instructions of the site engineer with all the necessary work. The price includes casting concrete type C (1:2:4) around the pipes 15cm thick for all pipelines.
Taps 1/2”: Provide materials and installation of chrome taps (best-approved type such as GROHE, DURAVIT, ECA, or Vitra) size 1/2” for the required places and according to the site engineer’s instructions.
Taps 3/4”: Provide materials and installation of chrome taps(best type as above) size 3/4” for the required places and according to the site engineer’s instructions.
Provide and install Sink basin Turkish marble type( two wings and two bowels); the price includes all pipe accessories for cold and hot water with the chrome mixer tap(Turkish quality) and also consists of the Aluminum counter length 1.8m for the Sink base.
Floor drain (PVC) 4” dia.: Provision of materials and erection of 4” dia. Floor drain. The work includes the excavations, crushed stone, lean concrete with a thickness of 20cm, and connection to the receiving manholes by PVC pipe 4” dia, with drain(Turkish quality) nickel covers, with all necessary work.
Provide materials and fix galvanized iron pipes 3” dia. For rainwater vertical draining from the roof with all fittings and accessories, according to the drawings and instructions of the site engineer.
Concrete block manholes: Supply materials and construction manholes of different depths with internal dimensions using solid concrete blocks size 15X20X40 cm for walls. The price includes excavation, supply, and laying of crushed stone with proper compaction, laying of plain concrete, block walls, plastering both sides (inner & outer), and covering the inner side of the manholes with a mix of 1:2 water, SBR. Aheen covers due to drawings with the frame, according to the details shown in the drawings.
40x40cm and cover 40x40cm
60x60 cm and cover 60x60cm
80x80 cm and cover80x80cm
Septic Tank: Provide materials and build a septic tank of internal dimension (L x W x D, 4 m x 3m x 2m under inlet pipe level), according to attached technical drawings and Supervisor Engineer instructions. The work includes excavations, cast reinforcement concrete with wood shuttering for slab floor, side & partition walls, and manhole neck of 25 cm thick, C26 Mpa, 12 mm steel bars @ 20x20 cm C/C double layers, with a thick nylon layer under concrete. The partition baffle wall should be at 2/3 from the inlet side. The baffle should have at least two holes (length 40cm, height 20cm). Paving inside of the septic tank by using waterproof waste materials of the approved sample. Fit T-joints on both inlet and outlet pipes, T-joints to being 20cm long on both ends. Cast top slap by reinforced concrete, 20 cm thick, steel bars 12mm @ 15cm c/c. The slab must fit smoothly and tightly onto the RC walls. Leave openings in the top slab for two manholes (20x20) cm each with neck extension, positioned exactly over the inlet and the outlet pipes. Close with two heavy-duty cast iron/GRP type manhole covers.
Install ventilation pipe PVC 2.5”. If possible, fix it to a close wall. Install min. 3m of 6” connection pipe between the septic tank outlet and the cesspool. Make sure the septic tank is fully watertight. The work includes excavations of a hole of suitable dimensions with a flat bottom, leaving a space of at least 20/30 cm around the tank. In the case of heavy ground (e.g., clayey subsoil and/or groundwater, the distance must be at least 50 cm. Spread a 20/25 cm deep layer of 2/6 washed gravel (JALMOOD) on the bottom of the excavation to allow the tank to rest on a uniform and level base. Excavated material must not be used as backfill. The excavation must be a minimum of 1 m from any structures. The work includes all required works for avoiding surface runoff infiltration, uplift pressure, and keeping the tank safe from any external forces and loads, marking the boundary with suitable warning signs.
Septic Tank: Provide materials and build a septic tank of internal dimension (L x W x D, 3m x 2m x 2m under inlet pipe level), according to attached technical drawings and Supervisor Engineer instructions. The work includes excavations, cast reinforcement concrete with wood shuttering for slab floor, side & partition walls, and manhole neck of 25 cm thick, C26 Mpa, 12 mm steel bars @ 20x20 cm C/C double layers, with a thick nylon layer under concrete. The partition baffle wall should be at 2/3 from the inlet side. The baffle should have at least two holes (length 40cm, height 20cm). Paving inside of the septic tank by using waterproof waste materials of the approved sample. Fit T-joints on both inlet and outlet pipes, T-joints to being 20cm long on both ends. Cast top slap by reinforced concrete, 20 cm thick, steel bars 12mm @ 15cm c/c. The slab must fit smoothly and tightly onto the RC walls. Leave openings in the top slab for two manholes (20x20) cm each with neck extension, positioned exactly over the inlet and the outlet pipes. Close with two heavy-duty cast iron/GRP type manhole covers.
Install ventilation pipe PVC 2.5”. If possible, fix it to a close wall. Install min. 3m of 6” connection pipe between the septic tank outlet and the cesspool. Make sure the septic tank is fully watertight. The work includes excavations of a hole of suitable dimensions with a flat bottom, leaving a space of at least 20/30 cm around the tank. In the case of heavy ground (e.g., clayey subsoil and/or groundwater, the distance must be at least 50 cm. Spread a 20/25 cm deep layer of 2/6 washed gravel (JALMOOD) on the bottom of the excavation to allow the tank to rest on a uniform and level base. Excavated material must not be used as backfill. The excavation must be a minimum of 1 m from any structures. The work includes all required works for avoiding surface runoff infiltration, uplift pressure, and keeping the tank safe from any external forces and loads, marking the boundary with suitable warning signs.
Construction of Cesspools: Provide materials and drill/build cesspools 1.1 m outer diameter for septic tank effluent infiltration according to attached drawings, 8 m depth. Casing (6 m) using double wall corrugated pipes of inner diameter 80 cm minimum and 1 m from the top/ground level by a concrete ring of min.80 cm dia. Gravel pack between cesspool wall and casing pipe. Concrete seal around the concrete ring, 0.5 m down from the top of cesspool/ground, the cover should be round ductile cast iron manhole covers 60cm diameter.
FINISHING: Including provision of all necessary materials, work, and curing. The works should be done according to sections 10 & 14 of IGTS, drawings, and instructions of the site engineer with all necessary works, and use SBR at a rate of 200gr per m2, the ratio of SBR to water(3-1).
Cement plastering: Providing materials and plastering with cement sand mortar 1:3 three layers (1. cement spatter dash(sharbat),2.rendering coat and leveling (kafmal),3. finishing fine coat (saf) ) 20mm thick min. and the final layer should be very smooth, using 3m straight aluminum edges for plastering guides for outer walls, main entrance, balcony, and corridors. And use SBR at a rate of 200gr per m2; the price includes fixing steel wire mesh for the edges between walls and columns.
Gypsum plastering: Supplying materials and plastering with gypsum (using the best type of gypsum approved by the site engineer) in 2 layers minimum thickness of 15mm using straight aluminum edges for plastering guides each 80 cm for walls and roofs, corridors, and entrance hall, and the area indicated in the drawings. The price includes spreading cement splatter dash, using SBR for the outer wall ( thermos tone ), fixing steel wire mesh for the edges between walls and columns, and using one layer of cement plastering to cover the wire mesh.
Ceramic tile works: supply materials and erection of (Turkish Quality) ceramic tiles (as sample approved) using best type(first class) on two-layer of plastering of cement mortar (1: 2) using straight edge for toilet walls, above all washbasins and baths walls, kitchens according to the details (the places indicated in the drawing or by the site engineer). The price includes the erection of ceramic belts with suitable height and coating the backside of the tiles with a layer of cement splatter dash using SBR. the price consists of using Aluminum straights for corners. And use SBR at a rate of 200gr per m2.
Skirting: Supply materials and skirting using Spanish ceramic tiles (15)cm height and cement mortar 1:3 in rooms, corridors, and main hall entrance according to the drawings and instructions of the site engineer. The price includes using a cement splatter dash with SBR at a rate of 30 Gr.\1 m.l.
Acrylic internal paint: Provide materials and Painting with Acrylic painting (Betek Or equivalent) painting and color approved by the site engineer) three layers for the rooms, corridors, and areas indicated in the drawings (inside the building) or indicated by the site engineer. The works should be done according to specifications, drawings, and instructions of the site engineer.
Note: the paint must be according to the international specification organization ISO 901.
External painting( silicone): Provide materials and Painting with External painting (Weather prove Betek or equivalents ) painting and color approved by the site engineer) three layers for the areas indicated in the drawings (for exterior walls). The works should be done according to the site engineer’s specifications, drawings, and instructions.
Note: the paint must be according to the international organization ISO 901.
Satin painting 120 cm: Provide materials and Painting 120 cm Hight with satin painting (Betek or equivalents ) painting and color approved by the site engineer) three layers for the areas indicated in the drawings (for walls).
Gypsum false ceiling: Provide materials and fix gypsum false ceiling 60*60cm for the Administration part and Hall or the places indicated by the site engineer. The price includes hanging beams (Skka 38 mm height) every 120cm by screw, steel fisher, rode 3mm, connecting the beams by skka 120cm,60cm long (32mm height ), and all necessary works.
Plastic false ceiling: Provide materials and fix the Plastic false ceiling 60*60cm for the places indicated by the site engineer. The price includes hanging beams (Skka 38mm height) every 120cm by screw, steel fisher, rode 3mm, connecting the beams by skka 120cm, 60 cm long (32mm height ), and all necessary works.
Doors & Windows: Providing all necessary materials and installing doors according to sections 11, 12, and 13 of IGTS, details, and instructions of site engineer with all the required works, prior samples should be approved by the site engineer.
Decorative Wooden Composite Doors(D2): Providing and installing standard decorative high-quality Composite wooden doors (white oak Canadian wood) Laminated thermoformed sheet water and the fire resistant colored well-known origin and brand (Turkish quality) made,200 mm minimum frame thickness and 100mm cornice outer measurement, double faces wooden plywood each face 8mm thickness, the sample should be provided for approval, The price includes installing 6 mm glass pans, switch (Italian made-three locks), gate lock, hinges, rubber, door stopper, and wooden frames, the price includes covering the bottom of the door with 15 cm aluminum plat for two faces.
MDF Wooden Panels: Provide and install MDF wooden panels (Turkish quality) approved and well-known to protect the walls with 18mm thickness and 15 cm Hight for classrooms; the price includes fixing the wall using screw bolts each 30cm and covering the top.
Decorative Metal Door Works(D1): Provide and install decorative metal doors (Turkish quality) approved well-known origin and brand for the entrances and halls and rooms, double-faced of plate thickness 1.50mm including glass pans, door frame 13.5*4.5cm 2.5mm thickness, Film Coated Residential Steel Entrance Door Glassy Finished Style, including special switch best type, gate lock, door stopper, rubber, polycarbonate filled, special guard bar, thermal paint & metal frames 6*22cm, Mercury glass 15x40cm with 3 cm Styrofoam polystyrene inside the door, Central lock system, with additional horizontal a lock with three concealed hinges with all necessary works, samples required for final approval.
Steel Guard Bars: Provide and install metal guard bars windows with primer and two layers of best oil paint, using iron pipe (4x2)cm 2mm thickness with all the required works.
Aluminum Windows: Supply material and install Aluminum windows wide section (high Turkish Quality) 2mm thickness, fixing 4x3cm 3mm thickness steel pipes frame to the wall, Double glass pan (6mm transparent+4mm semi-transparent) thickness, ordinary or mushajar, rubber, handle, the price includes flywire mesh for opening Areas, the work consists of using EKOPLAST paste, cleaning the glasses by machine before composing.
Aluminum Doors Works: Supply material and install Aluminum doors, double plate 2mm thickness best (Turkish quality). The price includes a double glass pan of 6mm thickness (Turkish quality), ordinary or mushajar, rubber, handle, switch mortice best Turkish type, and door stopper.
Metal Handrail Works: Provide materials & install a handrail for the fence and Front elevation decoration. The price includes primer and two layers of best oil paint for all ironmongery.
Metal handrail works for the walkways and retaining walls: Provide materials & install handrail on both sides of the entrance (walkway) with 90 cm Hight. The price consists of excavation and concreting (with dimension 30*30*50 cm ) for fixing square steel pipe 3” x 3” every 2m welded to the metal handrail. The price includes primer and two layers of best oil paint for all ironmongery required.
Metal handrail works for the stairs: Provide materials & install a handrail for the stair with Hight 85cm for the Administration sector. The price includes fixing jaw wood by screw and using sperto, Varnish due to details, painting with primer and two layers of best oil paint for all ironmongery, and all other required works.
Sign board: Supply and install steel sign board (2.5mX1.5m) plate gage 18, with steel angle frame (1.25x1.25) inch (3mm) thickness, with one layer of anti-rust paint and two layers of approved color oil paint (JOTIN) brand or equivalent, ISO 901, includes printing the name of the school with the foundation year by detail.
Steel ladder: Providing materials and fixing steel ladder using square pipe 2.5” for the edge and 2” (thickness 1.5 mm) for the interior. The price includes bracing, painting with one-layer primer, and three-layer best oil paint.
Supply materials and equipment to print the room address on an aluminium plate (30x15)cm and fix the allocated room’s wall.
Supply and install whiteboard ( 1.2*2.4 )m fixing the wall by bolts according to the ministry of education standards.
Flooring: (Including provision of materials, works, curing, and installation) the work should be done according to sections 6 and 9 of IGTS drawings and instructions of the site engineer with all necessary works.
Floor concrete:- Supply materials, equipment, and skilled labor for casting plain concrete 10cm thickness with Compressive strength of 28 days 210 kg/cm2 (1:2:4) above 10cm thick compacted crush gravel; the work includes grading and leveling smoothing the surface with a handheld vibrator or use a vibratory screed of the foundation under the tiles and tiger according to the details for the ground floor, using square steel pipes for leveling and formworks in stages.
Mosaic Tiles: Supply materials and paving mosaic tiles (40x40)cm, No.5 one-time polished, with all necessary works on a layer of cement sand mortar 1:3 mix ratio; the price includes repolishing the tiles after the end of the works. The work consists of using cement mortar and sealing the joints with white cement & lime grout and SPR colour if required mixture), making a 1.0 cm expansion joint each 25m2 filling with a flexible epoxy.
Beharton Tiles: Supply materials and paving shtyger beharton tiles,4.5cm thickness best quality (approved sample and color) with cement - sand mortar (1:3) not less than 5cm thickness, then filling the joints with yellow sand for walkways inside and outside the fence with all necessary works.
Natural Granite Tiles: Supplying materials and covering staircase with Natural Granite 3cm thickness (best quality and dimensions approved sample) with cement sand mortar 1:2 the price include cement splatter dash, with additives using a (1:2) solution of water and bonding agent(SBR concentrated %48 ) , the measurement will be done considering tread and riser.
Supply materials and paving Natural Granite 2 cm thickness (best quality and dimensions approved sample) with cement sand mortar 1:2 the price include cement splatter dash, with additives using a (1:2) solution of water and bonding agent(SBR concentrated %48 ). Note: ratio of mixing water and SBR is 1:3
EXTERNAL WORKS: Apron, walkways (inside building and outside the building), fence according to specification, attached drawings, and instructions of the site engineer.
Excavation works excavation in all types of soils(rock, asphalt, concrete), including backfilling and compaction, according to the requirement of section (3) of IGTS for the foundation. The price includes compaction of the base of excavation using a Viber-roller, according to the details.
The crushed stone works: Supply material and lay crushed stone 10 cm thick with good compaction for foundations.
Plain Concrete: Supply materials and cast plain concrete class (C10) 1:3:6 10cm (min. thickness) for under columns footing, wall footings, retaining wall, and foundation of a water tank stand to the required elevations and laying two layers of thick nylon. (The nylon should also cover the sides of excavation walls and extend on land 50cm to both sides of the excavation).
Solid concrete block works: Supply material & construction of walls with solid concrete blocks 15X20X40cm with cement and sand mortar(1: 3) for walkways: aprons, fence, and stand of water tank according to details. The price includes flush pointing for outside and inside by cement sand 1:3 .all required works should be carried out according to the attached drawing and specifications.
Hollow concrete block works: Supply material & construction of walls with Hollow concrete blocks (20X20X40)cm with cement mortar(1: 3) according to details. The price includes filling the vertical joints between blocks with cement and sand 1:3; all required works should be carried out according to the attached drawing and specifications.
Plain concrete (15cm thick): Providing materials and casting plain concrete (Smooth surface using concrete surface screed vibratory machine and copter instrument ) for parking area thickness 15cm with laying of 3/8 “dia steel bars at (30*30) cm spacing c/c making expansion joints every 2.5m in both direction or as required by cutter instrument filling the space by epoxy, the price includes using levelling steel forms for the edges.
Concrete for entrance walkway and Aprons: Supply materials and cast plain concrete 10cm thickness above 10cm thick compacted crush stone with expansion joint at 2.5m; the work includes grading, levelling, well compaction of the foundation soil, smoothening the surface of the concrete, according to the details. Straight steel shuttering should be used for joints, as shown in the drawings.
Cement plastering: Supply materials and plastering with cement mortar 1:3 two layers ( kafmal, saf ) thickness 20 mm. Min., and using a straight edge (the final layer should be very smooth). Using 3m straight aluminium, The work should be done according to specification.
External painting: Provide materials and Painting with External painting (Weatherproof Betek or equivalents high-quality painting and colour approved by the site engineer) in three layers for the areas indicated in the drawings (for exterior walls). The works should be done according to specifications, drawings, and instructions of the site engineer.
Note: the paint must be according to the international specification organization ISO 901.
Ready prefabricated Seats: Provide materials and fixing seats from composite material reinforced by fiberglass, weight 32.5 kg in different locations inside the fence (Turkish quality); the sample should be provided for approval; the price includes excavations, crushed stone 10cm, fair-faced plain concrete type (C) 1:2:4, 10 cm thickness for flooring(suitable area for sitting the seats) according to the details.
Ready prefabricated Garden(Picnic) Tables: Provide materials and fixing garden table from composite material reinforced by fiberglass, weight 45 kg in different locations inside the garden, (Turkish quality), the sample should be provided for approval, The price includes excavations, crushed stone 10cm, fair-faced plain concrete type (C) 1:2:4, 10 cm thickness for flooring(suitable area for sitting the seats) according to the details.
Plain concrete (12cm thick): Providing materials and casting plain concrete (Smooth surface using concrete surface screed vibratory machine and copter instrument ) for basketball play yard area thickness 12cm with using steel pipes shuttering 10x5 cm and making joint 2cm thick in three line and making expansion joints every 2.5m in both direction or as required by cutter instrument filling the space by epoxy, the price includes using leveling steel forms for the edges.
The price includes fixing a 10mm steel bar each 30 cm in two directions, installing steel pipe 5” for basketball and steel pipe 2.5” for handball, also painting the pipes with anti-rust paint and oil paint also painting the ground concrete with special paint for a play yard, and according to the game’s design and drawings, note: the concrete work should be done in two stages.
Screened Loam for Garden: Provide material and lay a layer of approved screened Loam 30 cm thick for the garden. The price includes grading, leveling, compaction of the base, planting grass with all requirements, also providing and laying 10x30 cm concrete block on a 10 cm thick and 20 cm width plain concrete using nylon sheet; the price includes providing a grass cutting machine, a well-known brand.
Main Metal Door: Provide and install metal door dimensions (2.1mX3.5m)according to the drawings with two face plates (1.25 mm) for the main gate using 3''x3” square steel pipe 6mm thick, primer + two layers of oil paint of all ironmonger as required, switch, metal frames, and decoration. The price includes the construction of two reinforced concrete columns(40x40)cm to fix the door. The price also includes casting reinforced concrete for the foundation of the columns (0.8x0.8)m and 20cm thick on a layer of 10 cm well compacted crushed stone with all necessary works.
Metal Door: Provide and install metal door dimensions (2.1mX3.0m)according to the drawings with two face plates (1.25 mm) for the main gate using 3''x3” square steel pipe 6mm thick, primer + two layers of oil paint of all ironmonger as required, switch, metal frames, and decoration. The price includes the construction of two reinforced concrete columns(40x40)cm to fix the door. The price also includes casting reinforced concrete for the foundation of the columns (0.8x0.8)m and 20cm thick on a layer of 10 cm well compacted crushed stone with all necessary works.
Metal Door: Provide and install metal door dimensions (2.1mX1.5m)according to the drawings with two face plates (gage 18) for the main gate using 3''x3” square steel pipe 6mm thick, primer + two layers of oil paint of all ironmonger as required, switch, metal frames, and decoration. The price includes the construction of two reinforced concrete columns(40x40)cm to fix the door. The price also includes casting reinforced concrete for the foundation of the columns (0.8x0.8)m and 20cm thick on a layer of 10 cm well compacted crushed stone with all necessary works according to the details and instructions of the site engineer.
Important Note:
- All the works should be done according to the International & Iraqi General Technical & Specifications (IGTS), Instructions of the supervision Engineer, UNHCR General Conditions of Contracts for Civil Works, and UNHCR General Conditions of the provision of mixed goods and services.
- UNHCR supervision engineers and its third-party partner engineers inspect the quality of the works implemented by the contractor. The work must be within engineering specifications/standards and timeframe.
- All the works should be done according to the International & Iraqi General Technical & Specifications (IGTS), Instructions of the supervision Engineer, UNHCR General Conditions of Contracts for Civil Works, and UNHCR General Conditions of the provision of mixed goods and services.
- The daily work is overseen by UNHCR supervision engineers and its third-party partner engineers.
- The contractor shall submit samples/catalogues of the materials to be used in the project to the supervision engineers for approval before the commencement of works. The supervision engineer can reject any material that does not comply with the specifications. The contractor should replace rejected materials without any extra cost.
- The Supervision Engineers can demand lab tests and a Certificate of Origin & Quality to ensure the quality of the material used and the work of the contractors.
- The contractor shall appoint a qualified site engineer and surveyor to represent him with 5 years of professional, relevant experience to work in such a project who should remain full-time on the sites during the contract period.
- The contractor should submit daily and weekly progress reports and will be endorsed by UNHCR supervision engineers and its third-party partner engineers.
- All the mentioned quantities in the BOQ are estimated and are subject to actual measurements after completion of the project.
- The contractor shall fix all damages to the existing pipeline, electric poles & cables, houses, streets & sewerage channels during the project implementation in the area. The contractor shall remove all debris and site waste after completion of works to dumping sites approved by the municipality.
- The contractor shall install (in full first) TWO steel signboards of 1.0 m x 1.2 m with calligrapher wages to achieve visibility of the project in accordance with UNHCR supervision engineers.
- The successful contractor will be required to complete all works as per the Drawings, Bill of Quantities, and Technical Specifications within 365 Days from the date of signing of the contract agreement and/ or site handover.
- The defect liability period is 365 Days, including all civil, electrical, and mechanical works.